Straining wire explained: what keeps chain link tight
Straining wire is the least visible part of a chain link fence and the one that decides how it looks a few years later. This guide explains what it does, how it works with the posts, and what to ask a contractor.
What is straining wire?
In short: a plain or coated wire that runs the length of a fence section, pulled tight between braced posts, which the mesh is tied to.
In Spanish it is called alambre tensor, and the small device that tightens it is a tensor. The wire runs horizontally along the fence, from one braced post to the next, usually at more than one height – near the top, near the bottom and often in between on taller fences.
The chain link mesh is tied to these wires. Because the mesh itself is flexible, the wires act as the skeleton along its length: they keep the top edge straight, stop the bottom from lifting and spread any load across many posts instead of one.
Why can't chain link just hang between posts?
In short: woven mesh stretches and folds under its own weight and any pressure, so it needs continuous support between posts.
Imagine a net hung between two poles. It sags in the middle, and the more you lean on it, the more it gives. Chain link is similar: the diamond pattern can close up or open out, so the mesh can change shape when something pushes on it.
Straining wires stop that. With a taut wire along the top, a dog jumping up or a branch falling on the fence is resisted along the whole section. With one along the bottom, an animal pushing underneath meets a tight edge rather than loose mesh. This is also why our guide on chain link for pets and poultry pays so much attention to the bottom wire.
How do straining wires depend on the posts?
In short: the wires are only as tight as the posts at each end allow – that is why end and corner posts are braced and set in concrete.
A tensioned wire pulls its end posts toward each other. If those posts are not braced, they lean, and the wire goes slack however well it was tightened. That is why end posts, corner posts and posts at a change of direction get diagonal braces, and why their footings matter.
Our page on posts and tensioning explains how we lay out braced and intermediate posts. The simple rule for owners: when comparing quotes, ask how many braced posts are included. Fewer braces is one of the easiest ways to cut a price, and one of the surest ways to get a sagging fence.
How can you tell if the tension has gone?
In short: a wavy top edge, a bottom edge that lifts easily, leaning corner posts or a snapped wire are the clear signs.
Walk the fence and look along it from one end. Signs that the tension has failed include:
- The top of the mesh dips between posts instead of running straight.
- The bottom edge lifts away from the ground when pushed.
- A corner or end post leans toward the fence.
- A straining wire hangs loose or has broken.
- Ties between mesh and wire have rusted through, so the mesh has slipped.
Some of these are small repairs; others mean the structure is failing. Our maintenance guide explains what to check each year.
Should straining wire match the mesh?
In short: yes – galvanised wire for galvanised mesh, coated wire for coated mesh, both for appearance and durability.
On a plastic-coated chain link fence, a bare silver straining wire stands out and the contrast is visible from a distance. Matching coated wire looks consistent. On a galvanised fence, galvanised wire and tensioners are the norm. Mixing metals or coatings at contact points can also encourage corrosion, which is another reason to keep the system consistent.
What should you ask a contractor about tension?
In short: how many straining wires, how many braced posts, how posts are set, and whether the wires can be retensioned later.
Good questions to put to anyone quoting your fence:
- How many straining wires will there be, and at which heights?
- Which posts will be braced, and how many braced posts are included in total?
- Are all posts set in concrete?
- Can the wires be retightened later without rebuilding?
A contractor who answers these clearly has thought about the structure, not just the mesh. We list them in our quotes; our article on red flags and common mistakes covers more of what to look for.
Articles and guides
Posts and tensioning: the structure behind a chain link fence
Chain link mesh has no strength of its own. Whether a fence stays tight or sags depends on the posts, their footings, the braces and the straining wires – the part most people never look at.
View details →
Galvanised chain link fence for rural plots in Málaga
Plain galvanised chain link is the workhorse of rural boundaries in Málaga province. We build it on concrete footings with braced posts and straining wire, so it stays straight and tight.
View details →
Chain link maintenance: what to check each year
A chain link fence needs little care, but not none. A walk along the line once a year, and after storms, catches small problems before they become a rebuild. This guide lists what to look at.
View details →Frequently asked questions
Is straining wire the same as barbed wire?
No. Straining wire is plain or coated wire used to support and tension the mesh. Barbed wire is a different product with a different purpose.
Can a chain link fence be built without straining wire?
It can be hung that way, but it will sag and deform much sooner. We always include straining wires on the chain link fences we build.
Why does the bottom wire matter so much?
It keeps the lower edge of the mesh tight, which is where animals push or dig. A loose bottom edge is a common escape route.
What is a tensor?
A small device fixed to the straining wire at a braced post that lets the wire be tightened. It also allows adjustment later on.
Does wire tension change with the seasons?
Steel expands slightly in heat and contracts in cold, and ground movement after rain can shift posts. Small changes are normal; large ones point to a structural problem.
Can over-tensioning damage a fence?
Yes. Too much tension can distort the mesh or pull posts out of line. The aim is firm, even tension, not maximum force.
Why do corners need braces if the wire is tight?
Because the tight wire is what pulls on the corner. The brace transfers that pull into the ground.
Can I add straining wire to an old fence?
Only if the posts can take it. On a fence with failing posts, adding tension makes the leaning worse.
How are the mesh and wire joined?
With tie wire wrapped at intervals along the straining wire and at the posts. Ties that rust through let the mesh slip.
Should I ask for straining wire in the quote?
Yes. A quote should say how many wires and braced posts are included, so you can compare offers fairly.
Send photos of your boundary
Photos and an approximate length are enough to start. We measure, then send an itemised quote with no commitment – even if you are not in Spain.